How to Program Your Overhead Door Codedogger or Genie Intellicode Keyless Entry
1. INSTALLATION INSTRUCTIONS
NOTE: For convenience in programming you may wish to install Wireless Keypad after Basic Programming of Wireless Keypad and Garage Door Operator(s) is completed.
- Mount wireless keypad on a flat vertical surface with enough room above to slide cover up. Pick location out of path of moving garage door and supporting hardware.
- Slide Keypad Cover up and pull off wireless keypad. Slide off battery cover and remove battery.
- Mark two holes by tapping a small nail through screw holes on keypad. Drill 1/16’ pilot holes then fasten with #6 screws enclosed. Replace Keypad cover.
- Replace battery and slide battery cover back into place.
2. BASIC PROGRAMMING
How to enter Personal Identification Number (PIN 1).
How to reset the Wireless Keypad memory.
A. PROGRAMMING THE WIRELESS KEYPAD
Entering PIN 1 ACTION KEYPAD INDICATOR
Open cover fully Blinks once and goes out
Press 3-5-7
Press “PROG” Blinks once each second
Enter PIN 1 (up to 8 digits)
Press “PROG” Double blinks each second
Close cover fully
NOTE: Your wireless Keypad is now ready to signal your Door Operator. Your Door Operator must be programmed to accept the signal from your Wireless Keypad.
Resetting the Wireless Keypad-------------------------------------------------------------------------------
- Open cover half way.
- Press and hold “PROG” and “8” while fully opening cover
- INDICATOR will blink once and go out.
- Close cover fully.
NOTE: Wireless Keypad memory is now set the same as when it left the factory.
Return to Entering PIN 1.
B. PROGRAMMING 1 DOOR OPERATOR
How to program your Door Operator to receive the signal from your Wireless Keypad.
************* WARNING *************
During this programming the Door Operator could begin to run. Be sure to stay away from the moving door and it’s parts. To prevent the door from moving, close door then disconnect it from the Door Operator by pulling the Red Emergency Release Handle.
Find the Learn Code Button and Radio Signal Indicator located on the Door Operator power head. Open Wireless Keypad Cover fully. This can be found where you see the antenna wire hanging from the motor head (you may have to take the lens cover off). If antenna wire is not hanging from motor head then you have an external receiver which is a black box approx. 6" x 2" mounted somewhere in the garage with a antenna wire hanging from it (pop off cover to find Learn Code Button).
ACTION KEYPAD INDICATOR
Press Operator Learn Code Button Blinks
Enter PIN 1
Press “SEND” Stays on
Press “SEND” Goes out
Press “SEND” to Test System Motor Runs.
Press “SEND” to Test System Motor Stops.
Use the Emergency Release to reconnect the Door to the Door Operator. Your system is now ready to use.
C. CONTROLLING 1 DOOR OPERATOR
ACTION KEYPAD INDICATOR
Open Cover Wait for Keypad indicator to go out before
Pressing any buttons.
Enter PIN1 Indicator blinks with each key press.
Press and hold "SEND" Door moves if only 1 door.
Close cover fully
NOTE: - if indicator is solid, PIN 1 was entered correctly.
- if indicator blinks, PIN1 was entered incorrectly. Close cover and start over.
C. CONTROLLING 1 DOOR OPERATOR
NOTE: Any Keypad button will control the door within 30 second after door begins to move or until cover is closed.
3. PROGRAMMING MULTIPLE DOOR OPERATORS
How to add Door Operators 2 and 3 to Wireless Keypad.
How to program your door Operator to receive the signal from your Wireless Keypad.
************* WARNING *************
During this programming the Door Operator could begin to run. Be sure to stay away from the moving door and it’s parts. To prevent the door from moving, close door then disconnect it from the Door Operator by pulling the Red Emergency Release Handle.
A. ADDING MORE DOORS TO THE WIRELESS KEYPAD
ACTION KEYPAD INDICATOR
Open cover fully Blinks once and goes out
Enter PIN 1
Press “PROG” Blinks once each second
Press “PROG” Double blinks each second
Press “PROG” Triple blinks each second
Enter total number of doors (2or3)
Press “PROG” Goes out
Close cover fully.
NOTE: Your Wireless Keypad is now ready to signal your door operators. Each Door Operator must be programmed to accept the signal from your Wireless Keypad. Decide which Door Operator will be Door 1, Door 2 and Door 3.
B. PROGRAMMING MULTIPLE DOOR OPERATORS
Find the Learn Code Button and Radio Signal Indicator located on the Door Operator power
Head Open Wireless Keypad cover fully.
ACTION RADIO SIGNAL INDICATOR
Press Operator Learn Code Button Blinks
Enter PIN 1
Press “SEND”
Enter Door Number (1,2or 3) Stays on
Press “SEND” Goes out
Press “SEND” to Test System Motor Runs
Press “SEND” to Test System Motor Stops
Close Wireless Keypad cover fully
Use the Emergency Release to reconnect the Door to the Door Operator. Your system is now ready to use. If you are programming another Door Operator go to that machine and repeat the above steps.
C. CONTROLLING MULTIPLE DOOR OPERATORS
ACTION KEYPAD INDICATOR
Open cover Wait for keypad indicator to go out
before pressing any buttons.
Enter PIN 1 Indicator blinks with each key press.
*Press “SEND”
*Enter Door Number (1,2 or 3) Door moves.
Close cover fully
NOTE: - if indicator is solid, PIN was entered correctly.
- if indicator blinks, PIN was entered incorrectly. Close cover and start over.
C. CONTROLLING MULTIPLE DOOR OPERATORS
NOTE: Any Keypad Button will control the door within 30 seconds after door begins to move or until cover is closed.
4. ENHANCED PROGRAMMING
How to add a Second Personal Identification Number (PIN2).
How to change Personal Identification Number (PIN 1 or PIN 2).
How to add and cancel a Temporary Personal Identification Number (PIN).
Changing a PIN ACTION KEYPAD INDICATOR
Open cover fully Blinks once and goes out.
Enter PIN to be changed
Press “PROG” Blinks once each second
Enter New PIN
Press “PROG” Double blinks if PIN 1 changed
Goes out if PIN 2 changed
Close cover fully
NOTE: Your Wireless Keypad is now ready to signal your Door Operator(s). Your Door operator(s) must be programmed to accept the signal from your Wireless Keypad.
SEE 2B PROGRAMMING 1 DOOR OPERATOR OR 3B PROGRAMMING MULTIPLE
DOOR OPERATORS.
Adding PIN 2 ACTION KEYPAD INDICATOR
Open cover fully Blinks once and goes out
Enter 1-5-9
Press “PROG” Blinks once each second
Enter PIN 2 (up to 8 digits)
Press “PROG” Goes out
Close cover fully
NOTE: Your Wireless Keypad is now ready to signal your Door Operator(s). Your Door Operator(s) must be programmed to accept the signal from your Wireless Keypad.
SEE 2B PROGRAMMING 1 DOOR OPERATOR or 3B PROGRAMMING MULTIPLE
DOOR OPERATORS.
Adding Temporary PIN
ACTION KEYPAD INDICATOR
Open cover fully Blinks once and goes out
Enter PIN 1
Press “PROG” Blinks once each second
Press “PROG” Double Blinks each second
Enter Temporary PIN
Press “PROG” Triple blinks each second
Close cover fully
NOTE: Your Wireless Keypad is now ready to signal your Door Operator(s). You do not need to reprogram your Door Operator(s).
Cancelling the Temporary PIN
The Temporary PIN will remain active until the next time PIN 1 is entered. Entering PIN 1 cancels the Temporary PIN.
Call us today at 800-542-0379 for Your Garage Door!